2008 Mitsu Evo X MR

This is why we get soo many custom exhaust here in CNY. This is a client we've had for years now, brand new Evo X. We've done his Audi S4, Prowler, Bmw 530Xi as well.





















Customer was adding his own personal tips down the road. This is a 100% custom setup 3" SS Tig and purge welded.

Enjoy.

Looks good, sound clip?

WOW, that is beautiful.


"Project 69'"
1969 Chevrolet C/10, 1/2 ton, 2wd
-Boosted LS1?
-Richmond ROD 6-speed(will get sometime)
-Posi 12-bolt(built w/eaton posi unit and richmond 3.73 gears)
-Disc brake and 5 lug swap
+little extras

now THATS pretty freakin sick

If only you guys weren't in New York....


But that looks killer, nothing but quality!!!!!!


Edited 1 time(s). Last edited Thursday, January 15, 2009 8:01 PM


Lanman31337 -F = fatties = do not want. A little chunk in the junk is ok though.

Looks amazing, I may have to drive up there so you can do my car

And wow, I really haven't ever seen an under body of a car look so clean.

very nice setup






RIP JESSE GERARD.....Youll always be in my thoughts and prayers...

Clean. Awesome work.

nicely done!

sound clip??

Unfortunately no sound clip. Ryan and Chris did this while I was away and didn't have the chance to snag a clip. I only got chris calling me and letting me hear it while he drove it around for the weekend. Lucky SOB....

But yea, customer loves it as usual. Thanks for the good CC everyone, we do appreciate it.

Mr. Kleindl wrote:now THATS pretty freakin sick

that.

and this

Wrong Turn wrote:If only you guys weren't in New York....


But that looks killer, nothing but quality!!!!!!

WiGM-Tuners member.

Work looks amazing. But why not full exhuast?

i forgot u lived near me... where's the shop located?

ecotecpower wrote:Work looks amazing. But why not full exhuast?

Its what the customer wanter... Axle back exhaust.

Sunbird- Port Byron 13140

Awesome work, those welds look Great!

It looks to me like the passenger side tip isnt quite centered. It looks like it is aligned a little bit towards the passenger side of the car, where as the left side looks exactly centered in the bumpers cutout. Could just be how it looks in the pics though of course:

Cody@RDFabs.com wrote:2008 Mitsu Evo X MR







Customer was adding his own personal tips down the road. This is a 100% custom setup 3" SS Tig and purge welded.

Enjoy.

Again, those welds are clean!

waaaaaaaaaaaaaay better than the hack job someone did on my caddy when I had it done...

I'll have to hit you up on my next car...



** FOR SALE** http://www.j-body.org/forums/read.php?f=24&i=110879&t=110879

I was also going to mention the exhaust. I am in no way bashing at all, because you guys have shown some amazing work, but the tiny bit of misalignment shows big because of the tight clearance in the exhaust cut outs on the bumper. is there a way you guys are able to easily scoot the passenger side tail pipe in just like the half inch or so that it is out?


On the other hand....you have other fingers.

In my family we teach that boys have a God-stick and girls have a Shame Cave. -John Stewart

It is the angle of the pics. Everything is put against a level and measured against the bumper for equal distances. The picture directly under the exhaust was taken more on the driver side than the passenger side, thus making it appear one side it off. You can look where the license plate is and see it favors the driver side rather than the passenger side.

If we had the tips the customer wanted installed, everything would look more even. But I assure you, we measure everything for clearance/alignment after it is all tightened and torqued down. Nothing leaves without being level.

Beautiful piece.


2010 Honda Fit LX