I was just looking on Ebay at boostcoolers and I have bought intercoolers from them before for my daytona shelby and they work amazingly. Well I found an intercooler that is overall 33x10x3, will this cooler fit in my front bumper? It is an 02 cavy with the wings west avenger front bumper. I am just concerned about the tubes fitting with that size 33 inches wide is including the spouts.

Thanks,
-Paul

My 30" fits behind my bumper, but barely. Depends on how you're going to run the charge pipes in the end, if you can wrap it around real tight and get around the braces in the front, then you should be alright.





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

You can make it work.




I was a retard, and now I'm permanently banned.

the 30" fits well with me too........

But 10" high might be alittle much ......... unless your going to put it BEHIND the rebar.......... but then your totally defeating the purpose of a LARGE intercooler........... just my thoughts...................................

Mines a 30 x 4 x 2 and this is how it fits.................

The top of the intercooler is butted up against the rebar................. and it hangs 4" down and thats how it looks......................



Hope that helps......

Lee


JDM Civic Hatch
Status: Parting Out Turbo Kit....
14.224 @ 102.01MPH @ 5.5psi.... 2.3 60'
Next: Civic JDM B16a2 w/GSR LSD Turbo - Goal 300whp 1400lbs...

I will have pics up soon on how i tucked my 10" tall intercooler in behind with out Cutting any bumper at all .... it sticks down a bit out from my RK sport lip kit because in the middle it goes up .. so i just orderd the other RK sport one... but i think with the Cavalier front bumpers it would have been fine..



The First Twin Charged jbody
blue car (R.I.P) - 240whp @7psi..
silver car - 305whp 315lbs.tq @15psi (91 Octane) or 420whp & 425lbs.TQ @20psi (94 octane+Alcohol Injection)
All dynos run on a Mustang dyno

Lee, that's uber sleeperish lol



www.kronosperformance.com / 732-742-8837

Lee wrote:the 30" fits well with me too........

But 10" high might be alittle much ......... unless your going to put it BEHIND the rebar.......... but then your totally defeating the purpose of a LARGE intercooler........... just my thoughts...................................

Mines a 30 x 4 x 2 and this is how it fits.................

The top of the intercooler is butted up against the rebar................. and it hangs 4" down and thats how it looks......................



Hope that helps......

Lee

i like that

NJHK (The JBO Negro) wrote:Lee, that's uber sleeperish lol

hahha thanks ................ well you'll be happy to know that I also now have a 2002 LS front lip ............... painted silver.......................... the best part about it ............

My friend was driving home ....... saw the lip on the side of the road.......................... hahahah so he picked it up ....... showed me ............... and I was like HOLY @!#$ ........ thats for my car ..... in my colour.......

so he said .... here............ now I gots me a nice front lip to complete the sleeper look ......... WOOT !!!!!!!!!!!!!

Thanks for the input Phlatcav and JBO NEGRO !!!!!!!!!!.......

haha

Lee


JDM Civic Hatch
Status: Parting Out Turbo Kit....
14.224 @ 102.01MPH @ 5.5psi.... 2.3 60'
Next: Civic JDM B16a2 w/GSR LSD Turbo - Goal 300whp 1400lbs...

Tee Hee

thats a PS2 btw

I have a 32x9x4 and it fits perfect. Well except that I had to cut the crash bar in half

Ecoclean wrote:I have a 32x9x4 and it fits perfect. Well except that I had to cut the crash bar in half

so now a minor fender bender will turn into you writing off your car !!!!

Good call !!



Lee


JDM Civic Hatch
Status: Parting Out Turbo Kit....
14.224 @ 102.01MPH @ 5.5psi.... 2.3 60'
Next: Civic JDM B16a2 w/GSR LSD Turbo - Goal 300whp 1400lbs...

its only a 5mph crash bar........ so I doubt its going to save anything. just dont hit anything.




SPD RCR Z - '02 Z24 420whp
SLO GOAT - '04 GTO 305whp
W41 BOI - '78 Buick Opel Isuzu W41 Swap

Cavy2Env wrote:I was just looking on Ebay at boostcoolers and I have bought intercoolers from them before for my daytona shelby and they work amazingly. Well I found an intercooler that is overall 33x10x3, will this cooler fit in my front bumper? It is an 02 cavy with the wings west avenger front bumper. I am just concerned about the tubes fitting with that size 33 inches wide is including the spouts.

Thanks,
-Paul

On a side note, i freakin love shelby Z's, what year is yours, and why in the hell arnt you souping that up? I have a friend whose got one, we're fully building the motor now (along with mine) and that thing will be a killer sleeper, a lot of people dont even know what it is, much less what its capable of, plus its still got pretty good after market.

It's an 89 Shelby and I already put in a forged motor with a T3-T4. I am going to have it dyno'd this summer but I wouldn't be suprised to see it hit 300 or so.