I'm planning to join up on 71. I'm assuming you guys to be rolling around here...830ish?
Anybody have any more input?
i was planning on leaving at 8ish, what exit are you at? im starting at 209 unless i gotta go get gorman or somethin lol
---
I'm at ashland, believe it to be 186
i be at....@!#$ i won't be seein 71
i can meet ya anywhere jesse
Well kyle, i'm just gonna jump on with the northern guys. So if you wanna let someone know where you'll be that works too.
I'll be at goasis between 815-830. If all goes accordingly
i plan on leaving my house at 8:00, i live literally 1 mile from the exit 209 truck stops so i should be to you before 8:30, is anyone coming from farther north? we can meet at one of the 209 truckstops at 8:00 and head out from there
or we could just plan on all meeting at jesse's exit at 8:30 and then go
Edited 1 time(s). Last edited Wednesday, July 23, 2008 3:18 PM
---
You buttheads just be on time!!
~2014 New Z under the knife, same heart different body~
______________________
WHITECAVY no more
2012 numbers - 4SPD
AUTOMATIC!!
328 HP
306 TQ
ill have the cav you guys call me or lmk where to be..ill be rippingthe head off the car and finishing this valve job nto the night..so lmk
Built&Boosted moar
04 Cavalier Turbo r.i.p my baby
2nd place 2009 GM tuner bash qwick 8--holla
I got a couple leaving Akron at 7am. We are going out 224 to 71 and down. Not to sure how far it is to ashland but I do know it's an hour to mansfield.
some one bring a t-bolt clamp to fit over my TB..im using and AEM CAI as my IC piping..worm clamps not holding up to 14psi..lol
Built&Boosted moar
04 Cavalier Turbo r.i.p my baby
2nd place 2009 GM tuner bash qwick 8--holla
how about we all just plan to meet at jesse's exit by 8:30?
---
What's a good location on that exit to meet up?
jnickel wrote:I'll be at goasis between 815-830. If all goes accordingly
so i would assume its close to the highway. jesse get your ass on here and give some input
---
goasis is the best place to meet. right next to the highway
can't miss goasis....you retarded if ya do
Matt Gorman(ECOjunkk) wrote:some one bring a t-bolt clamp to fit over my TB..im using and AEM CAI as my IC piping..worm clamps not holding up to 14psi..lol
I got you, I have 2.5" T-bolt clamps.
~2014 New Z under the knife, same heart different body~
______________________
WHITECAVY no more
2012 numbers - 4SPD
AUTOMATIC!!
328 HP
306 TQ
No Caravan for me. I just meet all you asses there.
WHITECAVY wrote:Matt Gorman(ECOjunkk) wrote:some one bring a t-bolt clamp to fit over my TB..im using and AEM CAI as my IC piping..worm clamps not holding up to 14psi..lol
I got you, I have 2.5" T-bolt clamps.
sweet i hope they fix my problem. see yall there
Built&Boosted moar
04 Cavalier Turbo r.i.p my baby
2nd place 2009 GM tuner bash qwick 8--holla
Me and matt are meeting at Rick Rousch Honda on rt. 18 in medina at 8:00AM if anyone wants to meet us there, then were rolling out to meet up with jesse and whoever else is at his exit, hopefully be there by 8:30 ish
---
sounds good to me. far as i know i'm the only one to worry about in ashland.
kyle...where you comin in at?
oh and matt i didnt have time to get the GPS from my buddy so your leading lol.
i was going to go get it today... but when i stopped to get a $15.00 oil change at midas and have them slap my new rotors on while i was there, some jackass aparently stripped both alan key holes in the drivers side caliper completely round, so they had to cut my caliper off. Long story short i have a whole new braking sysem up front and spent a lot more money than i intended to when i went in there
---
piss!! owel get me the address and ill use my phone..lol
Built&Boosted moar
04 Cavalier Turbo r.i.p my baby
2nd place 2009 GM tuner bash qwick 8--holla
ok we'll make jesse lead lol
---
