modified 2.4 bracket on HO mani - Performance Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
modified 2.4 bracket on HO mani
Saturday, March 12, 2005 6:56 PM
Iv'e done some searching but I haven't came up with anything. I want to use an RSM 62mm tb on my HO mani but I can't seem to find out any info about what you have to do to the tb bracket in order for it to work. any info would be great.



View my MySpace

Re: modified 2.4 bracket on HO mani
Saturday, March 12, 2005 9:01 PM
Easiest way it to use one from a 1995 Z24/GT.

Mark P.
Re: modified 2.4 bracket on HO mani
Sunday, March 13, 2005 1:40 PM
But I thought you only use that bracket when you use the 2.3 tb. I read some where that you can modify the 2.4 bracket for the 2.4 tb but I don't know what kind of modifying it needs.



View my MySpace
Re: modified 2.4 bracket on HO mani
Sunday, March 13, 2005 5:31 PM
i have all the hardware sitting in the garage from my 2.3.. might beable to help you out alittle
Re: modified 2.4 bracket on HO mani
Monday, March 14, 2005 2:47 PM
im listening....



View my MySpace
Re: modified 2.4 bracket on HO mani
Monday, March 14, 2005 10:46 PM
use the 2.4 bracket.



Click the banner to enter the best Quad4 & Twin Cam site on the internet.
Re: modified 2.4 bracket on HO mani
Monday, March 14, 2005 10:53 PM
me and peppers did an lo mani and we used the lo throttle cable bracket, however we bolted it to the tranny bolt right below the throttle body, just so happens that it was the perfect length away. hope that helps


_________________________________________________________________
EFFICIENCY DETECTIVE
Fast cars. I respect them ALL. Brand elitism is for fanbois and benchracers

daily: 99 civic Si
deceased: 95 cavy '00 LD9 auto swap (vandalized)
Re: modified 2.4 bracket on HO mani
Tuesday, March 15, 2005 9:23 AM
I want to use my 2.4 bracket I just don't really know what needs to be done to it in order for it to work



View my MySpace
Re: modified 2.4 bracket on HO mani
Tuesday, March 15, 2005 9:56 AM
should require no, you might have to adjust the throttle cable though, I installed the 2.3 TB on the HO and the throttle cable had slack afterward because I used the 2.3 bracket. You might not run into this problem but, you should be fine going with the 2.4 bracket with the TB.



Re: modified 2.4 bracket on HO mani
Tuesday, March 15, 2005 10:00 AM
we had shatloads of slack so we bolted the 2.3 bracket to the tranny bolt right below the new TB. jigga riggin baby


_________________________________________________________________
EFFICIENCY DETECTIVE
Fast cars. I respect them ALL. Brand elitism is for fanbois and benchracers

daily: 99 civic Si
deceased: 95 cavy '00 LD9 auto swap (vandalized)
Re: modified 2.4 bracket on HO mani
Tuesday, March 15, 2005 8:19 PM
or you could put a glob of JB Weld on the throttle cable at the pedal inside.




Re: modified 2.4 bracket on HO mani
Wednesday, March 16, 2005 2:58 AM
2.4 t/b, 2.4 bracket.... NO MODS. (just tap the one hole, and thread a bolt in, and drill the other 2 holes out to bolt to the intake, on the t/b) Just route the cable down, and under the batery tray..........

If you use a 2.3 t/b, use the 2.3 bracket, and some 'creative thinking' needs to go into shortening the throttle cable........ or bolt it to the trans like some have done.




SPD RCR Z - '02 Z24 420whp
SLO GOAT - '04 GTO 305whp
W41 BOI - '78 Buick Opel Isuzu W41 Swap

Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search